Installation and Operating ManualModel AP5660LTested &Listed byPortland Oregon USAOMNI- Test Laboratories, Inc.Report #:215-S-32-4SAFETY NOTICEPle
OperationAs a general rule, on lower feed rate settings, the damper should be farther to the left closing it off. On higher feed rates, the damper sho
CLEARANCES TO COMBUSTIBLESINSTALL ALL VENTS AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER!When your Pellet Stove Room Heater is being installed on
INSTALLING YOUR ROOM HEATERYou have already made the important decision of choosing your U.S. Stove Pellet Burning Room Heater; now your next step is
INSTALLING YOUR ROOM HEATER - continuedHORIZONTAL EXHAUST VENT INSTALLATIONFigure 8Listed Horizontal CapExhaust VentWall Thimble Mfg.by Pellet Vent Mf
INSTALLING YOUR ROOM HEATER - continuedFREESTANDING INTERIOR VERTICAL INSTALLATION1. Locate your Pellet Stove Room Heater in a location which meets
INSTALLING YOUR ROOM HEATER - continuedFREESTANDING EXTERIOR VERTICAL INSTALLATION1. Locate your Pellet Stove Room Heater in a location which meets t
INSTALLING YOUR ROOM HEATER - continuedSELKIRK DIRECT-TEMP VENT SYSTEM FOR PELLET STOVE HEATERSImages courtesy of Selkirk16
INSTALLING YOUR ROOM HEATER- continuedSELKIRK DIRECT-TEMP VENT SYSTEM FOR PELLET STOVE HEATERSUP AND OUT HORIZONTAL TERMINATION KITFIGURE 12Images cou
INSTALLING YOUR ROOM HEATER- continuedSELKIRK DIRECT-TEMP VENT SYSTEM FOR PELLET STOVE HEATERSSTRAIGHT OUT HORIZONTAL TERMINATION KITFIGURE 12Images c
INSTALLING YOUR ROOM HEATER - continuedSELKIRK DIRECT-TEMP VENT SYSTEM FOR PELLET STOVE HEATERSImages courtesy of SelkirkTHROUGH THE ROOF VERTICAL TER
TABLE OF CONTENTSTopic Page(s)Introduction ...
MOBILE HOME INSTALLATIONMobile home installation should be done in accordance with the Manufactured Home and Safety Standard (HUD), CFR 3280, Part 24.
VENT TERMINATION LOCATIONSFigure 2221
MAINTENANCEFAILURE TO CLEAN AND MAINTAIN THIS UNIT AS INDICATED MAY RESULT IN POOR PERFORMANCE AND HAZARDOUS SITUATIONS. CLEAN THE HEATER FREQUENTLY A
MAINTENANCE - continuedAsh Removal - Freestanding Unit:Remove the ashes periodically to avoid unnecessary ash build up. Ash removal is as follows:1. L
MAINTENANCE - continuedCleaningHeat Exchanger Tubes – Your Pellet Stove Room Heater is designed with a built in heat exchanger tube cleaner. This shou
MAINTENANCE - continuedChimney/Vent System Cleaning:1. Soot/Creosote Formation – When wood products are burned slowly, they produce tar and other orga
TROUBLE SHOOTINGSee replacement parts section for component locations.The heater will not light.• Check that the heater is plugged in and that the wa
TROUBLE SHOOTING - continuedThe 200o F High-limit switch has tripped.• Reset the switch and determine the cause. It is normally a faulty circulation
WIRING DIAGRAM28
REPLACEMENT PARTSContact your authorized U.S. Stove Pellet Burning Room Heater dealer to obtain any of these parts. Never use substitute materials. Us
IntroductionThe entire family of United States Stove Company thanks you for purchasing your new pellet burning room heater. At U.S. Stove, we build a
THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM YOUR KING OR ASHLEY, AND ENABLE YOU TO ORDER REPAIR PARTS CORRECTLY.KEEP THIS MANU
CUT HERE CUT HEREWARRANTY INFORMATION CARDName__________________________________________ Telephone #: (_____)_____________City____________________
CUT HERE CUT HEREFold Here Fold HereUnited States Stove CompanyP.O. Box 151South Pittsburg, TN 37380Fold HerePLACESTAMPHERE32
SAFETY INFORMATIONBe sure to read the entire owner’s manual prior to installing and operating this Pellet heater. Failure to follow these instruction
SAFETY INFORMATION - continuedKeep foreign objects out of the hopper. Contact your local building offi cials to obtain a permit and information on any
SPECIFICATIONSHeating Specifi cations:Burn Rate: *43,900 btu’s per hour or 5.1 lbs. of fuel per hourHopper Capacity: 55 lbs.*Dependent u
Assembly InstructionsSTEP 1Pull the factory installed wires out of the top of the stove. ere will be two wire harnesses, ash shown.STEP 2Unpack the
PANEL CONTROLSThe blowers and automatic fuel supply are controlled from a panel on the top of the 5660. The control panel functions are a follows.A.
DO NOT USE CHEMICALS OR FLUIDS TO START THE FIRE - NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR SIMILAR LIQ
Comentários a estes Manuais